M415D 2 phase stepper motor driver
Features
1. Using brand new imported chips, adoption of bipolar constant-current chopper technology
2. Low-noise, low-vibration and low temperature rising
3. Voltage 18-40VDC
4. With 7 stalls output current setting, peak current 1.5A
5. With 7 stalls microstep subdivision setting
6. Automatic Half current, motor wires misconnected protection
7. Internal optical isolation, highest frequency response 100KHZ
8. Suitable for current 0.21-1.5A 2 and 4 phase hybrid stepper motor
Current Selection:
| Peak | SW1 | SW2 | SW3 |
| 0.21A | off | on | on |
| 0.42A | on | off | on |
| 0.63A | off | off | on |
| 0.84A | off | on | off |
| 1.05A | off | on | on |
| 1.26A | on | off | off |
| 1.50A | off | off | off |
Microstep Selection:
| Pulse/Rev | SW4 | SW5 | SW6 |
| 200 | on | on | on |
| 400 | off | on | on |
| 800 | on | off | on |
| 1600 | off | off | on |
| 3200 | on | on | off |
| 6400 | off | on | off |
| 12800 | on | off | off |
Driver Functions Descriptions:
| Driver Function | Operating Instructions |
| Output Current Setting | Users can set the driver ouput current by SW1-SW3 three switches. The setting of the specific output current, please refer to the instructions of the driver panel figure. |
| Microstep setting | Users can set the driver Microstep by the SW4-SW6 three switches. The setting of the specific Microstep Subdivision, Please refer to the instructions of the driver panel figure. |
| Signal Interfaces | PUL is the setting pulse input, DIR is the stepper motor direction input, OPTO is the power supply for signal port+5V, ENA is the motor free input. |
| Motor Interfaces | A+ and A- are connected to a phase winding of the motor; B+ and B- are connected to another phase winding of the motor. If you need to backward, one of the phase windings can be reversed. |
| Power Interfaces | It uses DC power supply. Recommended operating voltage is 18VDC-40VDC, and power consumption should be greater than 100W |
| Installation Instructions | Driver dimensions:86*55*20mm, Please refer to dimensions diagram. Please leave 10cm spce for heat dissipation. During installation, It should be close to the metal cabinet for heat dissipation. |
Signal Interface Details:
The internal interface circuits of the driver are isolated by the opt coupler signals,
R in the figure is an external current limiting resistor. The Connection is differential.
And it has a good anti-jamming performance.
Control Signal and external interface.
| Signal amplitudes | External current limiting resistor R |
| 5V | Without R |
| 12V | 680Ω |
| 24V | 1.8kΩ |
Mechanical Dimension(mm):
Packing:
Cardboard boxes plus foam packaging. We can also pack the goods according to customer's requirements.
Certificate:
Transportation:
At present, our company supports a variety of modes of transport, or according to customer's needs to choose the mode of transportation.
FAQ:
1.Q: Can I get some samples first?
A: Sure, we are honored to offer you samples for your check.
2.Q: Do you have the products in stock?
A: Our products are manufactured according to your order except the normal products.
3.Q: What's the delivery time?
A: It usually takes about 7 working days,but the exact delivery time might be different for different order or at different time.
4.Q: How does your factory do regarding quality control?
A: Quality is priority. We always attach great importance to quality control from the beginning to the end of the production. Every product will be fully assembled and carefully tested before packed
Product Tags:
|
|
18-40VDC input 2 Phase Hybrid Stepper Driver M415D For NEMA11, 17,23 Stepping motor current less than 1.5A Images
|
